- Full Library Panel Bed: Item #123
Full Library Panel Bed: Item #123
SKU:
123
$3,100.00
$3,100.00
Unavailable
per item
Kit price: $3,100.00.
Dimensions: 119 1/2 inches wide by 88 inches high.
Please contact us before placing your order.Custom Handmade Furniture
100% American Made
Call 505-286-0856 for details
This is a deluxe Unit. This is the top of the line of Library beds I sell. I do sell less expensive of the same design. Call 505-286-0856
Compare to competition:
PLEASE GO TO MY STORE AND READ THE DESCRIPTION OF THE Queen SIZE PANEL BED. Then come back and read this additional information on the Library Bed. The size of the library bed is 117 1/2 wide by 88 inches high. This whole unit is pre-cut and drilled so all you have to do is assemble and install. The estimated time to paint or polyurethane is about 6 hours, the estimated time to assemble and install is 8 hours
We use a 11/16 stainless steel continuous track on the base and top of the cabinet.This track can be painted to match the cabinet. We use six steel rollers with ball bearings per sliding cabinet, these are rated at 60 pound each, these rollers (wheels) are 1 3/16" diameter sheaves. I mortice four of these wheels into the bottom of the rolling shelves. The upper track I mortise in two sheaves. The rolling shelves are 30 inches wide by 10 inches deep. I rabbit out the back end of these vertical panels for the 1/4 plywood backs,. The full depth of the shelves for the rolling cabinets is 9 inches for books, and the side cabinets are 15 inches deep. I build a floor base for the whole unit 130 inches long . On the very end of front of the cabinet runs a stainless steel track 5/16" high by 11/16" wide. This track and rollers are made to hold 300 pounds. The same track runs at the very top of the bed, with trim covering it up. This makes the rolling shelves locked in place so the won't come off the track.If for some reason the shelf should become detached from the upper track I have installed a scalp or trim that comes down over the sheaves so as to block the cabinet from falling forward away from the wall.The scalp is attached to a piece of plywood with the track on it, it runs continuous across the front of the unit and is screwed into the top of the vertical panels and front braces with 1 5/8 screws. This unit comes with 1/4 birch plywood backs on all four cabinets.
I brush on the stain. Wipe off the stain with a cloth, wait 8 hours and put 2-3 coats Satin water based polyurethane, sand with 220 grit sandpaper between coats,I like the Pro Series sold at Home Depot because it doesn't bubble up as much as the others and it is cheaper (as it is drying take the brush and lightly go over the surface to blow up those little bubbles.
If you would like talk to satisfied customers with the library bed please give me a call and I will get their telephone numbers to you. Dan 505-286-0856 or 505-470-8902
I am a member as Wallbeds by Bergman of the Better Business Bureau of the Southwest.
Please allow 3-4 weeks for the library bed.
On Sep-19-07 at 08:58:21 PDT, seller added the following information:
We now offer this unit finished with 3 coats of poly or unfinished. We now offer this unit shipped common carrier as a pre assembled kit with most parts assembled. Please call for quotes for your area.505-424-3634 and 505-470-8902
On Jan-08-08 at 08:02:27 PST, seller added the following information:
This unit is made out of 3/4 inch birch plywood, you can upgrade from there..The only difference between the Library Bed and the standard panel bed, in my E-Bay store is the front handle, as seen in the pictures. It has to have less depth so the shelf can slide by it. PLEASE GO TO MY STORE AND READ THE DESCRIPTION OF THE FULL SIZE BED. Then come back and read this additional information on the Library Bed. The size of the library bed is 117 1/2 wide by 88 inches high. This whole unit is pre-cut and drilled so all you have to do is assemble and install. The estimated time to paint or polyurethane is about 6 hours, the estimated time to assemble and install is 8-10 hours
We use a 11/16 stainless steel continuous track on the base and top of the cabinet.This track can be painted to match the cabinet. We use six steel rollers with ball bearings per sliding cabinet, these are rated at 60 pound each, these rollers (wheels) are 1 3/16" diameter sheaves. I mortice four of these wheels into the bottom of the rolling shelves. The upper track I mortise in two sheaves. The rolling shelves are 30 inches wide by 10 inches deep. I rabbit out the back end of these vertical panels for the 1/4 plywood backs,. The full depth of the shelves for the rolling cabinets is 9 inches for books, and the side cabinets are 15 inches deep. I build a floor base for the whole unit 130 inches long . On the very end of front of the cabinet runs a stainless steel track 5/16" high by 11/16" wide. This track and rollers are made to hold 300 pounds. The same track runs at the very top of the bed, with trim covering it up. This makes the rolling shelves locked in place so the won't come off the track.If for some reason the shelf should become detached from the upper track I have installed a scalp or trim that comes down over the sheaves so as to block the cabinet from falling forward away from the wall.The scalp is attached to a piece of plywood with the track on it, it runs continuous across the front of the unit and is screwed into the top of the vertical panels and front braces with 1 5/8 screws. This unit comes with 1/4 birch plywood backs on all four cabinets.
I use Min wax stain and wipe off the stain with a cloth, wait 8 hours and put 2-3 coats Satin water based polyurethane, sand with 220 grit sandpaper between coats,I like the Pro Series sold at Home Depot because it doesn't bubble up as much as the others and it is cheaper (as it is drying take the brush and lightly go over the surface to blow up those little bubbles.
If you would like talk to satisfied customers with the library bed please give me a call and I will get their telephone numbers to you. Dan 505-286-0856 or 505-470-8902
I am a member as Wallbeds by Bergman of the Better Business Bureau of the Southwest.
Please allow 3-4 weeks for the library bed.
On Sep-19-07 at 08:58:21 PDT, seller added the following information:
We now offer this unit finished with 3 coats of poly for $600.00. We now offer this unit shipped common carrier as a pre assembled kit with most parts assembled. Please call for quotes for your area.505-286-0858 and cell 505-470-8902.
This unit is shipped by Fed-Ex in Boxes of less than 80 pounds, for a total weight of about 500 lbs.
Prices vary up and down over time with different add-ons.
wallbedsbybergman.com
.
. Custom Sizes Always Available
505-286-0856
Dimensions: 119 1/2 inches wide by 88 inches high.
Please contact us before placing your order.Custom Handmade Furniture
100% American Made
Call 505-286-0856 for details
This is a deluxe Unit. This is the top of the line of Library beds I sell. I do sell less expensive of the same design. Call 505-286-0856
Compare to competition:
- Low to no off gassing of Formeldhyde, low carbon footprint,
- Solid plywood no particle board,
- 16 inch deep side cabinets,
- 1/4 plywood backs,
- No common carrier pallet shipping, first class Fed-Ex shipping in our own boxes,
- Rolling cabinets not hung from the top, weight is concentrated on the front bottom,
- heavy duty wheels, not cheap track,
- Complete plywood base under all cabinets,
- No bolting to floor.
- Heavy duty American made powder coated hinges for mattress compartment.
- American made solid (not hollow tube)powder coated metal flip over leg.
- BEST IN ITS CLASS
PLEASE GO TO MY STORE AND READ THE DESCRIPTION OF THE Queen SIZE PANEL BED. Then come back and read this additional information on the Library Bed. The size of the library bed is 117 1/2 wide by 88 inches high. This whole unit is pre-cut and drilled so all you have to do is assemble and install. The estimated time to paint or polyurethane is about 6 hours, the estimated time to assemble and install is 8 hours
We use a 11/16 stainless steel continuous track on the base and top of the cabinet.This track can be painted to match the cabinet. We use six steel rollers with ball bearings per sliding cabinet, these are rated at 60 pound each, these rollers (wheels) are 1 3/16" diameter sheaves. I mortice four of these wheels into the bottom of the rolling shelves. The upper track I mortise in two sheaves. The rolling shelves are 30 inches wide by 10 inches deep. I rabbit out the back end of these vertical panels for the 1/4 plywood backs,. The full depth of the shelves for the rolling cabinets is 9 inches for books, and the side cabinets are 15 inches deep. I build a floor base for the whole unit 130 inches long . On the very end of front of the cabinet runs a stainless steel track 5/16" high by 11/16" wide. This track and rollers are made to hold 300 pounds. The same track runs at the very top of the bed, with trim covering it up. This makes the rolling shelves locked in place so the won't come off the track.If for some reason the shelf should become detached from the upper track I have installed a scalp or trim that comes down over the sheaves so as to block the cabinet from falling forward away from the wall.The scalp is attached to a piece of plywood with the track on it, it runs continuous across the front of the unit and is screwed into the top of the vertical panels and front braces with 1 5/8 screws. This unit comes with 1/4 birch plywood backs on all four cabinets.
I brush on the stain. Wipe off the stain with a cloth, wait 8 hours and put 2-3 coats Satin water based polyurethane, sand with 220 grit sandpaper between coats,I like the Pro Series sold at Home Depot because it doesn't bubble up as much as the others and it is cheaper (as it is drying take the brush and lightly go over the surface to blow up those little bubbles.
If you would like talk to satisfied customers with the library bed please give me a call and I will get their telephone numbers to you. Dan 505-286-0856 or 505-470-8902
I am a member as Wallbeds by Bergman of the Better Business Bureau of the Southwest.
Please allow 3-4 weeks for the library bed.
On Sep-19-07 at 08:58:21 PDT, seller added the following information:
We now offer this unit finished with 3 coats of poly or unfinished. We now offer this unit shipped common carrier as a pre assembled kit with most parts assembled. Please call for quotes for your area.505-424-3634 and 505-470-8902
On Jan-08-08 at 08:02:27 PST, seller added the following information:
This unit is made out of 3/4 inch birch plywood, you can upgrade from there..The only difference between the Library Bed and the standard panel bed, in my E-Bay store is the front handle, as seen in the pictures. It has to have less depth so the shelf can slide by it. PLEASE GO TO MY STORE AND READ THE DESCRIPTION OF THE FULL SIZE BED. Then come back and read this additional information on the Library Bed. The size of the library bed is 117 1/2 wide by 88 inches high. This whole unit is pre-cut and drilled so all you have to do is assemble and install. The estimated time to paint or polyurethane is about 6 hours, the estimated time to assemble and install is 8-10 hours
We use a 11/16 stainless steel continuous track on the base and top of the cabinet.This track can be painted to match the cabinet. We use six steel rollers with ball bearings per sliding cabinet, these are rated at 60 pound each, these rollers (wheels) are 1 3/16" diameter sheaves. I mortice four of these wheels into the bottom of the rolling shelves. The upper track I mortise in two sheaves. The rolling shelves are 30 inches wide by 10 inches deep. I rabbit out the back end of these vertical panels for the 1/4 plywood backs,. The full depth of the shelves for the rolling cabinets is 9 inches for books, and the side cabinets are 15 inches deep. I build a floor base for the whole unit 130 inches long . On the very end of front of the cabinet runs a stainless steel track 5/16" high by 11/16" wide. This track and rollers are made to hold 300 pounds. The same track runs at the very top of the bed, with trim covering it up. This makes the rolling shelves locked in place so the won't come off the track.If for some reason the shelf should become detached from the upper track I have installed a scalp or trim that comes down over the sheaves so as to block the cabinet from falling forward away from the wall.The scalp is attached to a piece of plywood with the track on it, it runs continuous across the front of the unit and is screwed into the top of the vertical panels and front braces with 1 5/8 screws. This unit comes with 1/4 birch plywood backs on all four cabinets.
I use Min wax stain and wipe off the stain with a cloth, wait 8 hours and put 2-3 coats Satin water based polyurethane, sand with 220 grit sandpaper between coats,I like the Pro Series sold at Home Depot because it doesn't bubble up as much as the others and it is cheaper (as it is drying take the brush and lightly go over the surface to blow up those little bubbles.
If you would like talk to satisfied customers with the library bed please give me a call and I will get their telephone numbers to you. Dan 505-286-0856 or 505-470-8902
I am a member as Wallbeds by Bergman of the Better Business Bureau of the Southwest.
Please allow 3-4 weeks for the library bed.
On Sep-19-07 at 08:58:21 PDT, seller added the following information:
We now offer this unit finished with 3 coats of poly for $600.00. We now offer this unit shipped common carrier as a pre assembled kit with most parts assembled. Please call for quotes for your area.505-286-0858 and cell 505-470-8902.
This unit is shipped by Fed-Ex in Boxes of less than 80 pounds, for a total weight of about 500 lbs.
Prices vary up and down over time with different add-ons.
wallbedsbybergman.com
.
. Custom Sizes Always Available
505-286-0856